Unlock bootloader of Huawei devices.
Get binaries for Windows in the releases section. For Linux or macOS consider using the PotatoNV-crossplatform.
Follow the video guide or read the manual below.
- Are you sure you're actually using a Huawei/Honor device?
- Open the Settings → About phone. Check the CPU: it should be HiSilicon Kirin ***. If it is not your case (MediaTek, Qualcomm), then alas, your device is not supported. :(
- Okay, now you know CPU model. It should be one of these modification:
- Kirin 620
- Kirin 650
- Kirin 655
- Kirin 658
- Kirin 659
- Kirin 925
- Kirin 935
- Kirin 950
- Kirin 960
- 100% incompatible CPUs with PotatoNV: Kirin 710, 710A, 710F, 810, 970, 980, 985, 990 & newer.
- As for Kirin 710, 710F, 970 & 980, there is an alternative paid option — see the "Alternatives" section below.
The first step is the most difficult thing to do. You need to disassemble your device: this is necessary in order to access the contacts on the motherboard.
If you're not sure that you have enough experience to disassemble the device, then consider using paid software, that supports "software testpoint".
Warning
I strongly recommend watching video manuals for disassembling your device.
Warning
Be extremely careful with planar cables!
These cables are used in tablets, as well as in phones with a fingerprint scanner on the back cover.
You will need: a hair dryer, a guitar pick or a plastic card, conductive tweezers and maybe a screwdriver.
- Turn off the device.
- Heat the back cover evenly with a hair dryer.
- After a couple of minutes, try to stick the plastic card into the corner between case and lid, try to lift the edge and then deepen the card.
- Move around the perimeter of the back cover, peeling off glue.
- Now you can remove the back cover.
It's time to Google. You need to find the location of a special point on the motherboard – testpoint.
Note
If you are wondering why you need to do something with the unfortunate testpoint, then read the contents of the spoiler below.
To search, use the model name before the hyphen + "testpoint". For example for Honor 9 Lite (LLD-L31) you should Google "lld testpoint".
An example how a typical testpoint photo looks like.
The marks may vary:
- Only one point is marked in the photo.
- In the photo, a line is drawn between the point and the metal shield.
- In the photo, a line is drawn between two points.
Here you will need sleight of hand: try to short-circuit the point and the metal shield (in option 1 and 2), or short-circuit both points (option 3) with tweezers. Without removing the tweezers, connect the USB cable to the computer.
After 3 seconds, the tweezers can be removed.
Open the "Device Manager" – you should see an unknown device named USB SER
, or Serial Port HUAWEI USB COM 1.0
.
If the device has not been detected, make sure you are using a good cable, the tweezers are not a dielectric, and you are shorting the desired point.
- Install HiSuite.
- Install Huawei Testpoint Drivers.
- Download the latest release of PotatoNV.
- Start PotatoNV.
Note
All bootloaders are flashing to RAM, so an incorrect bootloader cannot harm the device.
Note
Disable FBLOCK
checkbox disables a special securtiy check. That modification allows you to flash/erase secure partitions or execute oem commands, that are not available with normal unlocking by unlock code [USERLOCK
].
Warning
FBLOCK
unlocking works correctly only on devices with Kirin 960 or Kirin 65x. Disabling this option can cause serious problems on legacy devices.
Okay, now refer to this table and select the appropriate bootloader.
Press the Start button. 🪄
The procedure will take no more than a minute. The program should write a new unlock code, keep it in a safe place.
Reboot your device to fastboot mode and execute following command on the host machine:
fastboot oem unlock YOUR_CODE_HERE
have fun.
Device | Model | Bootloader |
---|---|---|
Huawei P8 Lite (2015) | ALE |
Kirin 620 |
Huawei Y6II | CAM |
Kirin 620 |
Honor 5C / 7 Lite | NEM |
Kirin 65x (A) |
Honor 6X | BLN |
Kirin 65x (A) |
Honor 7X | BND |
Kirin 65x (A) |
Honor 9 Lite | LLD |
Kirin 65x (A) |
Huawei MediaPad T5 | AGS2 |
Kirin 65x (A) |
Huawei Nova 2 | PIC |
Kirin 65x (A) |
Huawei P10 Lite | WAS |
Kirin 65x (A) |
Huawei P20 Lite / Nova 3e | ANE |
Kirin 65x (A) |
Huawei P8 Lite (2017) | PRA |
Kirin 65x (A) |
Huawei P9 Lite | VNS |
Kirin 65x (A) |
Huawei Y9 (2018) | FLA |
Kirin 65x (A) |
Huawei MediaPad M5 Lite | BAH2 |
Kirin 65x (B) |
Huawei Nova 2i / Mate 10 Lite | RNE |
Kirin 65x (B) |
Huawei P Smart 2018 | FIG |
Kirin 65x (B) |
Honor 6 Plus | PE |
Kirin 925 |
Honor 7 | PLK |
Kirin 935 |
Huawei P8 | GRA |
Kirin 935 |
Honor 8 Pro / V9 | DUK |
Kirin 950 |
Honor 8 | FRD |
Kirin 950 |
Huawei P9 Standart | EVA |
Kirin 950 |
Honor 9 | STF |
Kirin 960 |
Huawei Mate 9 Pro | LON |
Kirin 960 |
Huawei Mate 9 | MHA |
Kirin 960 |
Huawei MediaPad M5 | CMR |
Kirin 960 |
Huawei Nova 2s | HWI |
Kirin 960 |
Huawei P10 | VTR |
Kirin 960 |
As far as I know, there is currently only one tool that can deal with newer CPUs — HCU Client.
This software requires a license, the most affordable plan is 3 days of access for €19.
See supported models by HCU Client here.
Note
Timed licenses locked to first used PC for two days. Therefore, it would be problematic to use such a license on more than one phone.
Disclaimer: I am not affiliated, associated, authorized, endorsed by, or in any way officially connected with UAB Digiteka, or any of its subsidiaries or its affiliates, including DC-Phoenix and HCU Client.
from https://github.com/mashed-potatoes/PotatoNV
No comments:
Post a Comment