Total Pageviews

Monday 25 May 2020

websocksy

Highly configurable dynamic WebSocket bridge.
websocksy is a highly configurable WebSocket (RFC6455) to 'normal' networking transport (TCP/UDP/Unix sockets) bridge. It is written in C and supports pluggable modules for bridge peer selection modules (for dynamic bridging) and stream framing.
It can be used to connect a wide variety of existing applications directly to a website, or to implement new functionality in a way that maintains compatibility between traditional network transports and WebSockets.

Table of contents

Motivation

Connecting WebSockets to 'real' sockets may seem like an easy task at first, but the WebSocket protocol has some fundamental differences to TCP and UDP.

Framing

Data sent over WebSockets is explicitly framed - you get told how much data to expect for any one package. This is similar to UDP, which operates on Datagrams, which are always received as one full message and carry an integrated length field.
In contrast to that, TCP operates on a 'stream' basis, where any message boundaries need to be established by an upper layer protocol, and any messages sent may be fragmented into multiple receive operations.
Bridging data from the WebSocket to the network peer is thus not the problem - one can simply write out any complete message frame received. For TCP, the other direction needs some kind of indication when to send the currently buffered data from the stream as one message to the WebSocket client.

Frame typing

WebSocket frames contain an opcode, which indicates the type of data the frame contains, for example binarytext, or ping frames.
Normal sockets only transfer bytes of data as payload, without any indication or information on what they signify - that is dependent on the upper layer protocols that use these transport protocols.

Contextual information

WebSockets carry in their connection establishment additional metadata, such as HTTP headers, an endpoint address and a list of supported subprotocols, from which the server may select one it supports.
Normal sockets only differentiate connections by a tuple consisting of source and destination addresses and ports, with the destination port number being the primary discriminator between services.

Dynamic proxying

To allow websocksy to connect any protocol to a WebSocket endpoint despite these differences, there are two avenues of extensibility.

Peer discovery backends

Peer discovery backends map the metadata from a WebSocket connection, such as HTTP headers (e.g. Cookies), the connection endpoint and any indicated subprotocols to a peer address naming a 'normal' socket.
Backends can be loaded from shared libraries and may use any facilities available to them in order to find a peer - for example they may query a database or scan a file based on the supplied metadata. This allows the creation of dynamically configured bridge connections.
Currently, the following peer address schemes are supported:
  • tcp://[:] - TCP client
  • udp://[:] - UDP client
  • unix:// - Unix socket, stream mode
  • unix-dgram:// - Unix socket, datagram mode
The default backend integrated into websocksy returns the same (configurable) peer for any connection.

Peer stream framing

To solve the problem of framing the data stream from TCP peers and selecting the correct WebSocket frame type, websocksy uses "framing functions", which can be loaded as plugins from shared objects. These are called when data was received from the network peer to decide if and how many bytes are to be framed and sent to the WebSocket, and with what frame type.
The framing function to be used for a connection is returned dynamically by the peer discovery backend. The backend may select from a library of different framing functions (both built in and loaded from plugins).
websocksy comes with the following framing functions built in:
  • auto: Send all data immediately, with the text type if the content was detected as valid UTF-8 string, otherwise use a binary frame
  • binary: Send all data immediately as a binary frame
  • separator: Waits until a variable-length separator is found in the stream and sends data up to and including that position as binary frame. Takes as parameter the separator string. The escape sequences \r\t\n\0\f and \\ are recognized, arbitrary bytes may be specified hexadecimally using \x
  • newline: Waits until a newline sequence is found in the stream and sends data up to and including that position as text frame if all data is valid UTF-8 (binary frame otherwise). The configuration string may be one of crlflfcrlfcr specifying the sequence to look for.

Configuration / Usage

websocksy may either be configured by passing command line arguments or by specifying a configuration file to be read.
The listen port may either be exposed to incoming WebSocket clients directly or via a proxying webserver such as nginx.
Exactly one backend can be active at run time. Specifying the backend parameter a second time will unload the first backend and load the requested one, losing all configuration. Options will be applied in the order specified to the backend loaded at the time.

Command line arguments

  • -p : Set the listen port for incoming WebSocket connections (Default: 8001)
  • -l : Set the host for listening for incoming WebSocket connections (Default: ::)
  • -k : Set the inactivity timeout for sending WebSocket keep-alive pings (Default: 30)
  • -b : Select external backend
  • -c : Pass configuration option to backend

Configuration file

If only one option is passed to websocksy, it is interpreted as the path to a configuration file to be read. A configuration file should consist of one [core] section, configuring central options and an optional [backend] section, configuring the current backend. Options are set as lines of  pairs.
In the [core] section, the following options are recognized:
  • port: Listen port for incoming WebSocket connections
  • listen: Host for incoming WebSocket connections
  • ping: Inactivity timeout for WebSocket keep-alive pings in seconds
  • backend: External backend selection
In the [backend] section, all options are passed directly to the backend and thus are dependent on the specific implementation. Backends should provide their own documentation files.
An example configuration file using the file backend is available in the repository.

Default backend

The integrated default backend takes the following configuration arguments:
  • host: The peer address to connect to
  • port: An explicit port specification for the peer (may be inferred from the host if not specified or ignored if not required)
  • framing: The name of a framing function to be used (auto is used when none is specified)
  • protocol: The subprotocol to negotiate with the WebSocket peer. If not set, only the empty protocol set is accepted, which fails clients indicating an explicitly supported subprotocol. The special value * matches the first available protocol.
  • framing-config: Configuration data for the framing function

Plugins

This repository comes with some plugins already included, in addition to the built-in backend and framing functions. Documentation for these resides in the plugins/ directory.

Building

To build websocksy, you need the following things
  • A working C compiler
  • make
  • gnutls and libnettle development packages (nettle-dev and libgnutls28-dev for Debian, respectively)
Run make in the project directory to build the core binary as well as the default plugins.

No comments:

Post a Comment